Keurig K Cup Coffee Maker Manual

The Keurig K Cup Coffee Maker is a single-serve brewing system designed for convenience and variety. It uses pre-packaged K-Cup pods to brew a fresh cup of coffee, tea, or other hot beverages in under a minute. Key features include multiple cup size settings, a removable drip tray, a water reservoir, an energy-saving auto-off function, and a descaling alert. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Brewing Instructions 7. Maintenance & Cleaning 8. Descaling Procedure 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Brewer with K-Cup pod holder, Removable Drip Tray, Water Reservoir, Control Panel, Power Cord.

Feature	Description
K-Cup Pod Holder	Holds and punctures the K-Cup pod for brewing
Water Reservoir	Removable tank for holding water; capacity varies by model
Control Panel	Buttons for power, brew size selection, and optional settings
Removable Drip Tray	Catches spills; adjustable for different cup heights
Brew Size Selector	Choose cup size (e.g., 6oz, 8oz, 10oz)
Power Button	Turns the brewer on/off
Descale Indicator Light	Alerts when descaling is needed
Auto-Off Feature	Automatically powers down after a period of inactivity
Energy Saver Mode	Reduces power consumption when not in use
Hot Water Button	Some models dispense hot water without a pod

Installation & Setup

Unpack and inspect contents. Place on a clean, stable, and level surface near a power outlet.

Remove all packaging materials from inside and outside the brewer.
Wash the water reservoir and drip tray with warm, soapy water. Rinse and dry thoroughly.
Fill the water reservoir with fresh, cold water and place it back onto the brewer.
Plug the power cord into a standard 120V AC outlet.
Place a large mug on the drip tray.

WARNING! Do not use the brewer without water in the reservoir. Ensure the brewer is on a heat-resistant surface away from edges.

First-Time Use

Prime the brewing system before first use to ensure optimal performance.

Power on the brewer. The power button will illuminate.
Lift and close the brewer handle (without a K-Cup pod) to run water through the system.
Select the largest brew size. Press the brew button to start a cleansing brew cycle.
Discard the water from the mug. Repeat this process 2-3 times with fresh water.
Your brewer is now ready for use with K-Cup pods.

CAUTION! The water and brewed beverage will be hot. Handle with care to avoid burns.

Specifications

Product Type: Single-Serve Coffee Maker.
Brewing Technology: K-Cup Pod System.
Brew Sizes: Typically 6oz, 8oz, 10oz (model dependent).
Water Reservoir Capacity: Varies by model (e.g., 48oz, 60oz).
Power: 120V AC, 60Hz, 1470W.
Dimensions: Varies by model.
Weight: Varies by model.
Warranty: Typically 1-year limited warranty.
Compatible Pods: Keurig K-Cup pods and Keurig-licensed pods.

Controls and Settings

Access functions via the control panel buttons. Front Panel: POWER, BREW SIZE (Small, Medium, Large), HOT WATER (if available).

Indicator Lights: Power On, Heating, Ready to Brew, Add Water, Descaling Alert.

Settings: Brew strength control (on select models), Auto-off timing (adjustable in some models: 2hrs default), Temperature control (on select models).

Brewing Instructions

Brews coffee, tea, hot cocoa, and other beverages using K-Cup pods.

Ensure the brewer is powered on and the "Ready" light is illuminated.
Lift the handle and place a K-Cup pod in the pod holder. Close the handle firmly.
Place your mug on the drip tray.
Select your desired brew size by pressing the corresponding button.
Press the BREW button. Brewing will begin and complete automatically.
After brewing, lift the handle to eject the used pod into the storage compartment (if equipped).

Tip: For a stronger brew, select a smaller cup size. Pre-warming your mug with hot water can improve temperature retention.

Maintenance & Cleaning

Regular cleaning ensures best performance and taste.

Exterior: Wipe with a soft, damp cloth. Do not use abrasive cleaners or immerse in water.
Drip Tray & Reservoir: Remove and wash weekly with warm, soapy water. Rinse and dry.
Pod Holder Assembly: Lift the handle and wipe the needle and funnel area with a damp cloth to remove coffee grounds.
Descaling: Perform when the "Descale" light illuminates or every 3-6 months. See Descaling Procedure.

CAUTION! Always unplug the brewer and allow it to cool completely before cleaning. Never use vinegar to descale; use Keurig Descaling Solution or approved alternative.

Descaling Procedure

Mineral buildup from water can affect performance. The "Descale" light will indicate when it's needed.

Purchase Keurig Descaling Solution or an approved citric acid-based descaler.
Empty and rinse the water reservoir.
Fill the reservoir with the entire bottle of descaling solution, then top off with water to the MAX fill line.
Place a large mug (at least 16oz) on the drip tray.
Press the POWER button to turn the brewer off, then press and hold the 10oz and 12oz brew buttons simultaneously for 3 seconds to enter descale mode (process may vary by model).
Follow the on-screen prompts or indicator lights. The brewer will run multiple brew cycles without a pod.
After the solution tank is empty, rinse the reservoir thoroughly and refill with fresh water.
Run multiple brew cycles with just water (no pod) until the reservoir is empty to rinse the system.
The descale light will turn off when the process is complete.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. UL Listed. Copyright © Keurig Green Mountain, Inc. Keurig, K-Cup, and the Keurig logo are trademarks of Keurig Green Mountain, Inc., registered in the U.S. and other countries. For support, visit www.keurig.com or contact 1-866-901-2739.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Brewer won't power on	No power/outlet issue	Ensure plug is firmly in outlet; try a different outlet; check household circuit breaker.
No water flow / small brew	Clogged needle/descaling needed	Unplug brewer. Use a paperclip to gently clear the exit needle. Perform descaling procedure.
Brew is not hot enough	Pre-heat cycle incomplete	Ensure "Ready" light is on before brewing. Run a water-only brew cycle to pre-heat the system.
Water leaks	Reservoir not seated/overfilled	Ensure reservoir is correctly placed and locked. Do not fill above MAX line. Check for cracks.
Pump sounds loud/grinding	Low water/air in line	Refill water reservoir. Run several water-only brew cycles to purge air from the pump.
"Add Water" light on but reservoir is full	Float stuck	Remove reservoir, check the float on the bottom moves freely. Gently tap to unstick.
Pod not punctured	Handle not closed fully	Open and firmly re-close the handle. Ensure no pod is obstructing closure.

Reset: Unplug the brewer for 2 minutes, then plug it back in.

Service: 1-866-901-2739; www.keurig.com